{"id":4308,"date":"2024-09-13T10:01:25","date_gmt":"2024-09-13T08:01:25","guid":{"rendered":"https:\/\/help.fetura.pl\/knowledge-base\/how-to-configure-ipsum\/"},"modified":"2026-07-23T00:25:16","modified_gmt":"2026-07-22T22:25:16","slug":"how-to-configure-ipsum","status":"publish","type":"ht_kb","link":"https:\/\/help.fetura.pl\/en\/knowledge-base\/how-to-configure-ipsum\/","title":{"rendered":"How to configure IPSUM?"},"content":{"rendered":"\n

Navigating to the configurator<\/h2>\n\n\n\n

To configure IPSUM, go to the Settings<\/strong> tab.<\/p>\n\n\n\n

\"Fetura<\/figure>\n\n\n\n

Then go to the Feeding<\/strong> tab.<\/p>\n\n\n\n

\"Settings<\/figure>\n\n\n\n

Find the IPSUM dispenser settings<\/strong> tab and enter it.<\/p>\n\n\n\n

\"Feeding<\/figure>\n\n\n\n

A list of IPSUMs added to the farm will appear, select the ones you want to configure.<\/p>\n\n\n\n

\"IPSUM<\/figure>\n\n\n\n

Configuration<\/h2>\n\n\n\n

Mode of operation<\/h3>\n\n\n\n

On this panel it is possible to set:
– How much maximum feed in one dose can be dispensed by the dispenser [1]<\/strong>
– What is the size of the initiating dose [2]<\/strong>
– In which mode of operation the dispenser is [3]<\/strong>
– What is the responsibility of the button on the dispenser [4]<\/strong>
– How the amount of dispensed feed is measured (time \/ pulse) [5]<\/strong>
To save the changes, click the button [6]<\/strong>.<\/p>\n\n\n\n

\"Work<\/figure>\n\n\n\n

Engine settings<\/h3>\n\n\n\n

On this panel, it is possible to set:
– How long minimally the motor can run [1]<\/strong>
– In case of setting the performance measurement in time, what should be the interval time between dispensing doses [2]<\/strong>
– In case of setting the performance measurement in pulses, what should be the time between pulses [3]<\/strong>
– After what time the motor overloads [4]<\/strong>
– After what time the absence of the animal is detected [5]<\/strong>
To save the changes, click the [6]<\/strong> button.<\/p>\n\n\n\n

\"Motor<\/figure>\n\n\n\n

IPSUM configuration – sensors<\/h3>\n\n\n\n

On this panel, it is possible to set:
– In what mode should the sensor in the feed machine operate [1]<\/strong>
– In what mode should the sensor in the dispenser operate [2]<\/strong>
– What should be the stock of feed spilled above the sensor in the trough [3]<\/strong>
To save the changes, click the [4]<\/strong> button.<\/p>\n\n\n\n

\"Ipsum<\/figure>\n\n\n\n

Efficiency<\/h3>\n\n\n\n

On this panel it is possible to set:
– Efficiency in time, if the issued feed is measured by time [1]<\/strong>
– Efficiency in pulses, if the issued feed is measured by pulses [2]<\/strong>
To save the changes, click the [3]<\/strong> button.<\/p>\n\n\n\n

\"Efficiency<\/figure>\n\n\n\n

IPSUM configuration – weight<\/h3>\n\n\n\n

On this panel, you can set:
– Standard deviation (by how much the average weight of the animal can fluctuate) [1]<\/strong>
– What is the minimum detected weight that IPSUM should take for analysis [2]<\/strong>
– From what time, IPSUM takes weight measurements [3]<\/strong>
To save changes, click the [4]<\/strong> button.<\/p>\n\n\n\n

\"IPSUM<\/figure>\n\n\n\n

Strain gauge beams<\/h3>\n\n\n\n

On this panel it is possible to set to which inputs the strain gauge beams are connected [1]<\/strong>, to save the changes click the button [2]<\/strong>.<\/p>\n\n\n\n

\"Strain<\/figure>\n\n\n\n

Scale<\/h3>\n\n\n\n

On this panel it is possible to set the scale for the inputs to which the strain gauge beams are connected [1]<\/strong>, to save the changes click the button [2]<\/strong>.<\/p>\n\n\n\n

\"Scale<\/figure>\n\n\n\n

Automatic tare<\/h3>\n\n\n\n

On this panel it is possible to set:
– What minimum weight must be detected for taring to turn on [1]<\/strong>
– For how long the scale must tare [2]<\/strong>
– Every how many minutes the scale must tare at least once [3]<\/strong>
To save the changes, click the [4<\/strong> ]<\/strong> button.<\/p>\n\n\n\n

\"Automatic<\/figure>\n\n\n\n

NRF power<\/h3>\n\n\n\n

On this panel it is possible to set at what power the NRF antennas operate [1]<\/strong>, to save the changes click the [2]<\/strong> button.<\/p>\n\n\n\n

\"NRF<\/figure>\n\n\n\n

Information about the animal going off the scale<\/h3>\n\n\n\n

On this panel you can set whether IPSUM should inform you when the animal goes off the scale [1]<\/strong>, to save the changes click the [2]<\/strong> button.<\/p>\n\n\n\n

\"Information<\/figure>\n\n\n\n

CAN notifications<\/h3>\n\n\n\n

On this panel it is possible to set whether CAN notifications are to be sent [1]<\/strong>, to save the changes click the [2]<\/strong> button.<\/p>\n\n\n\n

\"CAN<\/figure>\n\n\n\n

<\/p>\n\n\n","protected":false},"excerpt":{"rendered":"

Navigating to the configurator To configure IPSUM, go to the Settings tab. Then go to the Feeding tab. Find the IPSUM dispenser settings tab and enter it. A list of IPSUMs added to the farm will appear, select the ones you want to configure. Configuration Mode of operation On this…<\/p>\n","protected":false},"author":4,"comment_status":"open","ping_status":"closed","template":"","format":"standard","meta":{"footnotes":""},"ht-kb-category":[121],"ht-kb-tag":[],"class_list":["post-4308","ht_kb","type-ht_kb","status-publish","format-standard","hentry","ht_kb_category-ipsum-en"],"_links":{"self":[{"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb\/4308","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb"}],"about":[{"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/types\/ht_kb"}],"author":[{"embeddable":true,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/comments?post=4308"}],"version-history":[{"count":4,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb\/4308\/revisions"}],"predecessor-version":[{"id":15038,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb\/4308\/revisions\/15038"}],"wp:attachment":[{"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/media?parent=4308"}],"wp:term":[{"taxonomy":"ht_kb_category","embeddable":true,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb-category?post=4308"},{"taxonomy":"ht_kb_tag","embeddable":true,"href":"https:\/\/help.fetura.pl\/en\/wp-json\/wp\/v2\/ht-kb-tag?post=4308"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}